Robert Bosch Placement 
    Paper
    
      
        
        
          
            
            
              
                
                
                  
                    Paper Type : Technical - Electronics  
                    Test Date : 17 February 2007  
                     
                    ROBERT BOSCH PAPER ON 17th FEBRUARY  
                     
                    hai, I am pradeed. here I am submiting ROBERT BOSCH question 
                    paper. There will be seperate papers for ELECTRONICS 
                    students and COMPUTER students. Here which I submited is for 
                    ELECTRONICS students 
                     
                    SECTION 1(TECHNICAL)  
                     
                    1. There was a figure of JK flip flop in which ~q is 
                    connected to J input and K=1. If clock signal is 
                    successively applied 6 times what is output sequence (q=?) 
                    d) 010101  
                     
                    2. Frequency response of a filter is 
                    a) Range of frequencies at which amplification of signal is 
                    employed. 
                    b) Output voltage versus frequency (plot) 
                    c) Filter which suppresses particular frequency 
                     
                    3. Gain and bandwidth of an op amp is 
                    a) Independent of each other 
                    b) Gain decreases as bandwidth decreases 
                    c) Gain increases as bandwidth increases till some extent 
                    after which stability decreases 
                     
                    4. There was a figure of 4:1 MUX in which A and B are select 
                    lines. Inputs S0 and S1 are connected together and labeled 
                    as C where as S2 and S3 are connected together and labeled 
                    as D. Then which of the following is true? 
                    a) Y= B+C 
                    b) Y= A+C 
                    c) Y= A+B 
                    d) Y= C+D (Where Y is the output) 
                     
                    5. In step up transformer (or Step down… not sure) 
                    transformation ratio is 1:5. If the impedance of secondary 
                    winding is 16 ohm then what is the impedance of primary 
                    winding? 
                    a) 80 b) 3.2  
                     
                    6. There was a circuit consisting of AC voltage source and 
                    one inductance. Inductance value=0.2mH (or 0.2uH or 0.2H not 
                    sure).AC voltage =150 sin (1000t).what is the current 
                    flowing in the circuit? 
                    a) i= 7.5 sin (1000t) 
                    b) i= -7.5 sin (1000t) 
                    c) i= 7.5 cos (1000t) 
                    d) i= -7.5 cos (1000t) 
                     
                    7. Power gain of an amplifier having i/p gain of 20W and 
                    output gain of 20mW is 
                    a) 60 b) 25 c) 10 d) 0 
                     
                    8. There was a RC circuit given with AC voltage source. 
                    Expression for capacitance was asked for charging condition. 
                    Choices were somewhat like this: a) some value multiplied by 
                    exp (-t/T) 
                    ans --c i= (Vs/R)exp(-t/ T) 
                     
                    9. 2’s complement of -17  
                    ans -- 01111 
                     
                    10. Instrumentation amplifier is used for--------- --? 
                    a). effective shielding 
                    b). high resective filters 
                    c). high common mode 
                    d). all the above. 
                     
                    11. In “ON CHIP” decoding memory can be decoded to 
                    a) 2^n b)2^n +1 c)2^n -1 d) some other choice 
                     
                    12. Half of address 0Xffffffff is 
                    a) 77777777 b) 80000000 c) 7FFFFFFF d) some other choice 
                     
                    13. Which one of the following is used for high speed power 
                    application? 
                    a) BJT b) MOSFET c) IGBT d) TRIAC 
                     
                    14. One question related with SCR rotation angle given 
                    ifring angle is 30degree 
                    ans - 150degree 
                     
                    15. SCR is used for 
                    a) To achieve optimum (or maximum ...not sure) dv/dt 
                    b) For high current ratings 
                    c) To achieve high voltage 
                    d) Some other choice 
                     
                    16. State in which o/p collector current of transistor 
                    remains constant in spite of increase in base current is 
                    a) Q point b) Saturation c) Cut off 
                     
                    17. A 16 bit monosample is used for digitization of voice. 
                    If 8 kHz is the sampling rate then the rate at 
                    which bit is transferred is 
                    a) 128 b) 48 c) d) 
                     
                    18. To use variable as recursive, variable should be used as 
                    a) Static b) Global c) Global static d) Automatic 
                     
                    19. what is the resonant frequency of parrel RLC circuit of 
                    R= 4.7 komh L= 2 micro Henry and c=30pf. 
                    a). 20.5 MHz 
                    b). 2.65 KHz 
                    c). 20.5 KHz 
                    d). none 
                     
                    20.for the parallel circuit (one figure is given) Is= 10mA. 
                    R1= 2R, R2=3R, R3= 4R. R is artritary 
                    a). 3.076mA 
                    b). 3.76mA 
                     
                    21. main () 
                    { 
                    int a=0x1234; 
                    a=a>>12; 
                    a=a<<12; 
                    printf (“%x”, a); 
                    } 
                    What is the output? 
                    a)1000 b) 2000 c) d) None of these 
                     
                    22. What does (*fun () []) (int) indicate? 
                    ans...b). an array of pointer to a functions that an int as 
                    parameter and return int. 
                     
                    23. #define A 10+10 
                    main () 
                    { 
                    int a; 
                    a=A*A; 
                    printf (“%d”, a); 
                    } 
                    a) 100 b) 200 c) 120 d) 400 
                     
                    24. One more question related with ADC like voltage is 8 
                    volts. freqency 2 Mega hz. what is the converssion rate  
                     
                    25. Question related with serial in parallel out shift 
                    register…What is output sequence? 
                    Ans..... 1010 
                     
                    26. Given one RLC circuit in which values of R, L and C were 
                    given. What is the value of frequency f? 
                     
                    27. if (fun ()) 
                    { 
                    X++; 
                    } 
                    X gets incremented if and only if 
                    a) fun () returns 0 
                    b) fun () return 1 
                    c) fun () return -1 
                    d) return a value other than 0 
                     
                    28. In dynamic memory 
                    a) Power dissipation is less than that of static memory 
                    b) Clock is needed 
                    c) Refreshing is required 
                    d) All the above 
                     
                    29. Short, int and long integers have how many bytes? 
                    a)2,2,4 b) Machine dependant c)2,4,8 d) Some other choice 
                     
                    30. A (n) is -----------filter combination of 
                    a) Passive b) Active c) AMPLIFIER d) BOOSTER 
                     
                    31.Mobility of electron is 
                    a) Increases as temperature increases 
                    b) Decreases as temp decreases 
                    c) Independent of conductivity 
                    d) Some other choice 
                     
                    32. Structure comparison is done 
                    a). yes 
                    b) no 
                    c) compiler dependent 
                    d) 
                     
                    33. The system in which communication occurs in both ways 
                    but not simultaneously in both ways is 
                    a) Half simplex b) Simplex c) Half duplex d) duplex 
                     
                    34. main () 
                    { 
                    int a=5, b=6; 
                    int i=0; 
                    i=a>b? a:b; 
                    printf (“%d”, i); 
                    } 
                    a) 0 b) 1 c) 6 d) 
                     
                    35. int fun (char c) 
                    { 
                    int i; 
                    static int y ;} 
                    a) c, i are stored in stack and y stored in data segment 
                    b)c stored in stack and i,y are stored in data segment 
                    c) c is stored in text segment, y in data and i in stack 
                     
                    36. main () 
                    { 
                    int *p; 
                    short int i; 
                    p= (char *) malloc (i*10); (code was showing error here) 
                    p+=10; 
                    printf (“%d”, p); 
                    } 
                    Value of p? 
                     
                    37. main () 
                    { 
                    int *p,i[2]={1,2, 3}; 
                    p=i; 
                    printf (“%d %d %d”, i [0],*p,*p+1) ; 
                    } 
                     
                    38. F = A'B' + C' + D' + E' then 
                    A) F = A+B+C+D+E 
                    B) F= (A+B)CDE 
                    C) F = AB(C+D+E) 
                    D) F= AB+C+D+E 
                     
                    39. how would you insert pre-written code into a current 
                    program? 
                    a) #read  
                    b) #get  
                    c) #include  
                    d) #pre  
                     
                    40.structure may contain 
                    a) any other structure 
                    b) any other structure expect themselves 
                    c) any other structure except themselves and pointed to 
                    themselves 
                    d) none of the above 
                     
                    41. three boys x,y,z and three girls x,y,z... sit around a 
                    round table . but x does not want any girl sitting to him 
                    and girl y does not want any boy sitting next. how many ways 
                    can they be seated. 
                    a) 2 
                    b) 4 
                    c) 6 
                    d) 8 
                     
                    42. k is brother of n and x. y is the mother of n and z is 
                    is the father of k . which of the following statement is not 
                    definitely true. 
                    a) k is the son of z. 
                    b) y is the wife of z. 
                    c) k is the son of y. 
                    d) n is the brother of x. 
                     
                    43. find the lateral surface of a prism with a triangular 
                    base if the perimeter of the base is 34 cm. and the height 
                    is 45 cm. 
                    a) 765 square cm. 
                    b) 3060 square cm. 
                    c) 1530 square cm. 
                    d) none 
                     
                    44.Given a< b< c < d . what is the max ratio of given 
                    equation 
                    a) (a+b)/(c+d)  
                    b) (b+c)/ (a+d)  
                    c) (c+d)/ (a+b)  
                    d) (a+c)/ (b+d) 
                     
                    45. A and B starts moving from points X and Y simultaneously 
                    at a speed of 5kmph and 7kmph to a destination point which 
                    is of 27 km from points X and Y. B reaches Y earlier than A 
                    and immediately turns back and met Z. Find the distance XZ. 
                    ans.... 22.5 km 
                     
                    46. Ann is shorter than Jill and Jill is taller than Tom. 
                    Which of the following inferences are true? 
                    a) Ann is taller than Tom b) c) d) Data insufficient 
                     
                    47. A and B starts from same point at opposite direction. 
                    They will move 6km and take 8km left. How Far is A and B 
                    from each other? 
                    ans ...20m 
                     
                    48.6440 soldiers are to be arranged in the shape of square. 
                    If 40 soldiers were kept out then the number of soldiers 
                    making each straight line is?  
                    Ans --80 
                     
                    49. Sum of squares of two numbers is 404 and sum of two 
                    numbers is 22.Then product of two Numbers? 
                    a) 20 b) 40 c) d) (Answer is 40. Two numbers are 20 and 2) 
                     
                    50. In an examination 4 marks are assigned for correct 
                    answer and 1 mark is deducted for wrong answer. However one 
                    student attempted all 60 questions and scored 130.Number of 
                    questions he attempted correct is? 
                    a) 35 b) 38 c) 42 d) 35 
                     
                    51. Each ruby is of 0.3 kg and diamond is of 0.4 kg.Ruby 
                    costs 400 crores and diamond costs 500 crores. Ruby and 
                    diamonds have to be put into a bag. Bag cannot contain more 
                    than 12 kg.Which of the following gives maximum profit (or 
                    in terms of wealth) (In crores) 
                    ans ...only ruby 40p 
                     
                    52. the cpu stack is placed in .... 
                    a). cpu resister 
                    b). RAM 
                    c). ROM 
                    d). hard disk 
                     
                    53). (10 | 7) would produce 
                    a). 17 
                    b). 3 
                    c). 11 
                    d). 15 
                     
                    ENGLISH section 
                    fill in the blanks...... .. the answers is  
                    61) a). impounded b). protected c). hounded d). relegated. 
                    62).a). oblinion b). authertiory c). dejection d). 
                    deso....... 
                    63).a). subdued b). bountiful c). tentative d). ardem. 
                    64).a). b). esulcant c). emblerratie d). innate 
                    65).manor -- d). n. the landed estate of a land or nobleman. 
                    66).neologism -- c). n. giving a new meaning to an add word. 
                    67).batten -- b). n. a narrow strip of wood. 
                    68).tepid -- d). adj. lacking interest enhusi...., luewarm 
                    69. discerning -- d). adj. distinguishin one thing from 
                    another, having good judgment 
                     
                    BEST OF LUCK 
  | 
                   
                 
                 | 
               
             
             | 
           
         
         | 
       
     
       |