GE Placement-Paper on Jul 26, 2013

Discussion in 'Latest Placement papers' started by krishna, Nov 14, 2013.

  1. krishna

    krishna Banned

    Paper pattern

    For Electrical – 10 Aptitude and 10 Technical questions.

    For Civil – 10 Aptitude and 10 Technical questions.

    For Mechanical – 10 Aptitude and 10 Technical questions.

    For Electronics – 10 Aptitude questions.

    For Computer Science – 10 Aptitude and 10 Technical questions in C.

    Duration of test 30 minutes. Each correct answers carries 1mk .


    Note: Negative marking of ¼ mark exists for each wrong answer.

    Getting through the written test is quite easy. Then we had Technical interview followed by HR interview.

    This paper is for Electrical students. Hope aptitude is almost same for all branches, only technical paper is different.

    Aptitude paper

    1. The time taken by boat to row upstream 2km and downstream 6km is same. Calculate the speed of boat in still water.
    a) 4kmph b) 8kmph c) 2kmph
    Ans a

    2. A, B, C can finish a piece of work in 12 days. A alone can finish the same work in 20 days. B alone can finish the same work in 18 days. In how days C alone can complete the same work.( numbers are not accurate but question is of this type).

    3. The fungus in a vessel doubles for every 5minutes.at 3.00 P.M the fungus in the vessel is 120. at what time the fungus rate is 960.
    Ans 3.15 P.M

    4. The size of the room is 120x80 and the size of each tile is 2.4x1.8. Find minimum number of tiles required to cover the floor (number are not accurate)

    5. A triangle inscribed in a circle is given and asked to find out the angle. (A bit tough question among all the questions)

    6. AB and CD are two chords of a circle. AB=2*CD. The perpendicular distance ofchords AB and CD from the center of the circle are a, b respectively. Express AB in terms of a, b.

    7. A pipe can fill tank in 3 hrs. A hole a bottom of tank can empty the tank in 6 hrs. After ½ hr the hole at the bottom of tank is opened. Find the time taken to fill the tank completely. (Numbers are not accurate. Problem of this model is given)

    8. Problem on figures is given. Some sequence of figures (around 5) are given and asked to find the next figure that comes in sequence.

    Technical paper
    1. In dc motor the motion of conductor is given by
    a) Flemming’s right hand rule
    b) Fleming’s left hand rule
    c) Cork screw rule
    Ans b.

    2. The resistance of conductor is R. If the conductor length gets doubled and cross section is reduced by half a times then the resistance of conductor is
    a).R remains same
    b) R gets reduced by 2
    c) R increases by 2
    d) R increases by 4
    Ans d.

    3. Two plates of cross section 2mm2 are separated by a distance of 1cm. the capacitance between these plates is
    ( I don’t remember exact figures, question of this to compute the value of capacitance C = €A/d)

    4. No of poles, speed of the alternator, etc are given and asked to find the voltage induced in the rotor ckt of the alternator.

    5. In parallel circuit under resonance
    a) current is maximum
    b) impedance is minimum
    c) voltage magnification takes place
    d) current magnification takes place

    6. 3 resistances of R/2 are connected in star , the magnitude of resistances when connected in delta is
    Ans 3R/2

    7. Problem on dual networks
    Sorry I could not recall remaining questions. For aptitude R.S.Agarwal aptitude
    R.S.Agarwal verbal and non verbal reasoning are more than enough. For technical just
    prepare basic concepts in networks and machines.

    Technical interview

    This is the basic elimination round. My interview lasted for about 45 to 50min.
    Before attending the interview just have a very good brush up in all the electrical subjects especially power systems protection, machines, power system operation and control, power electronics and drives.
    Answer all questions with great confidence . Be cool. GE people are very friendly. Dont give up any question quite easily Try till last they will help you at most of times. Try to answer all the questions. Once you get through this round they will ask you to stay back for next round.

    HR interview.
    This is very very cool round among all the rounds.95% its not elimination round. Here they test your communication skills and your problem handling capability.
    For me it was just 30-40min.For one of my friend it lasted for about 1and ½ hr.
  2. krishna

    krishna Banned

    GE PAPER ONH 5TH NOVEMBER AT KHARAGPUR

    (1) Written test -----

    (a) Aptitude test common for all branch.

    (b) Five type of paper in Stress analysis, CFD, Chemical Engg, Electrical & Instrumentation, C- language test.

    I attended CFD ----- there were 10 questions in aptitude and 10 in Fluid and heat- - transfer.

    Some questions are as follows based on my memory –

    (1) What is the probability of getting a two digit number which is multiple of 2 and 3 both?

    (2) One insect is trying to climb on a pole and in each second it goes for some height but it slips down for some distance …..in how much time it will get on the top…? (I am missing some numerical values but….i hope u have got my point)

    (3) One helicopter start to fly from Delhi at 2 pm with speed 600 kph for the distance 2400km but after start of its journey its on of engine got failed and then pilot reduces its speed 400 kph ….now he become 80min late….Find that at what time engine failed?

    (4) Calculate the max area of rectangle that is inscribed in a 14 cm radius circle?

    (5) One question form BAR CHART?

    (6) One question from work and wages?

    (7) Max number that is devisable by three consecutive even numbers?

    (8) ---

    (9) ---

    (10) --- Thermal & Fluid

    (1) What is Kirchoff’s law?

    (2) What is the adiabatic flame temperature?

    (3) What is the analogy of Grasoff’s number in forced convection (Ans –Pr)?

    (4) What is the Neumann’s BC & Drichlet’s BC?

    (5) What is the work that is obtained when the pressure and volume changes from P1to P2 and V1 to V2?

    (6) What is the max to average velocity ratio in turbulent tube flow?

    (7) Relation in viscous sub layer ….( Ans U+=y+)?

    (8) Raleigh Number’s significance?

    (9) ---

    (10) ---

    After I got selected in written ….I appeared for Tech Interview and then HR interview

    Tech interview is basically elimination process and questions were from the Project work .

    HR interview is 95% selective process…

Share This Page